Download Article

Download Article

When it comes to keeping your business firm and car warm in the winter and cool in the summer, the cardinal is proper insulation. One way to help seal up doors and windows in your business firm is to install agglutinative weather stripping around the frames. Don't forget to spiral on a sweep at the bottom of whatsoever outside doors to keep out hot or cold air, also. If you lot want to insulate your motorcar, use adhesive to secure weather stripping along the door jamb. Hello, energy efficiency!

  1. 1

    Pare away any erstwhile atmospheric condition stripping. Installing weatherstripping is a great way to cover a window or door for winter. If your door or window currently has weather condition stripping, remove it before you place the new slice down. If the one-time stripping is agglutinative, pull it off using your hands. If information technology's screwed into the frame, use a drill or screwdriver to take out the screws, then lift off the stripping.[1]

    • Try using a putty knife to brand it easier to pare away the old conditions stripping. That will make information technology easier to scrape away tape and any modest pieces.[2]
    • If yous removed any screws, fix them bated so you lot can utilize them on the new stripping.

  2. ii

    Scrub off whatsoever sticky residue with an adhesive remover. If the leftover glue from the quondam stripping doesn't peel off easily, utilise an adhesive remover with a material and scrub the area. So dry it with a clean cloth.

    For actress stubborn adhesive that yous can't get off with the remover, sand it away with a fine-grit sandpaper. Wait for a paper that is between 120 and 220-grit and run information technology over the rest.

    Advertisement

  3. three

    Clean the door or window jamb with soap and water, and then dry out information technology. This removes any remaining residue or droppings, which could bear on how well your new stripping sticks in identify. With a cloth, wipe down the entire frame of the door or window with lather and warm water. Employ another cloth to dry off the frame.[three]

    • If at that place are any small holes or cracks in the frame, load a tube of outside caulk into a caulk gun, then pull the trigger to squeeze the paste into the pigsty. Let it dry out for about 24 hours before applying your stripping.

  4. 4

    Measure the top and side of your door or window frame. Hold ane finish of a record mensurate against the inside edge of the frame, and then stretch it to the other inside border to determine the length of the elevation and/or lesser piece of stripping. To measure the sides, identify the end of the tape measure on the inside edge of the top of the frame and pull the record down to the floor.[4]

    • Measure twice to make sure you accept the virtually accurate reading.
    • Information technology may help to have someone else read the measurement while you agree the tape in place.

  5. 5

    Select the type of agglutinative conditions stripping to utilise based on your door. The 3 nearly common types of adhesive atmospheric condition stripping are foam, V strip, and rubber or vinyl. Adhesive-backed foam tape is the most popular, as it's the easiest to install, just if you have a draftier door frame, yous might prefer vinyl. Consider the specifics of your door or window when choosing your weather condition stripping.[5]

    • V strip may also exist labeled as "tension seal."
    • You can observe adhesive weather stripping at a hardware store or online retailer.
    • Weather stripping comes in different thicknesses, and so it's a good idea to buy a few unlike sizes, and then effort them out with your door. If the weather stripping yous utilize is besides thick, your door might not close properly.[half-dozen]
    • Buy as much weather stripping as you demand based on your measurements, plus 10% extra every bit a precaution. For example, if yous demand 96 inches (240 cm) for your window, buy 106 inches (270 cm) of stripping.

    How to Choose a Type of Weather Stripping

    For the cheapest and easiest solution, go with foam record. Information technology costs less than $1 per 1 ft (0.30 1000).

    If you don't desire to exist able to meet the atmospheric condition stripping, cull V strip. Information technology's nearly invisible when installed correctly!

    For old doors or windows that have large gaps, employ prophylactic or vinyl conditions stripping. The tubular pieces seal upwardly cracks better.

  6. 6

    Cut your pieces of weather stripping to the correct length. Mark the length that you measured on the weather stripping using a pencil. Then trim the slice at the marked spot with a utility knife or pair of sturdy scissors.[7]

    • If you're weather stripping a window, you'll need iv pieces, i for the top, ane for the bottom, and 1 for each side.
    • To atmospheric condition strip a door, you need ane slice for the top and 1 piece for each side, for a total of 3 strips. The lesser of the door will require a door sweep.

  7. 7

    Line 1 piece of stripping along the side of the door or window frame. Start by placing the end of the conditions stripping in the top corner of the jamb. And then, adapt the rest of the piece and so it lies flush against the door frame.[8]

    • Install the conditions stripping when the outside temperature is at least l °F (10 °C) to assist the adhesive concord amend.
    • If you're using V strip, place the stripping against the frame so that the opening of the V faces towards the outside of the door or window.
    • Practise not put the atmospheric condition stripping on the door itself.

  8. 8

    Peel off the backing and printing the stripping firmly into identify. Once you have the stripping aligned where y'all want it to get, remove the paper bankroll from the piece. Run your easily along the piece and apply pressure to secure the sticky side of the stripping to the door or window jamb.[9]

    • To prevent the stripping from sticking to things information technology shouldn't, peel a piddling flake of backing off at a fourth dimension as you go, instead of removing it all at once.
    • For actress protection, you lot can secure the stripping into place by hammering nails through it into the frame, or use a staple gun to insert heavy-duty staples into it.

  9. 9

    Repeat on the other side and elevation of the frame. Install the remaining pieces around the door or window by removing the bankroll and pushing the adhesive against the jamb. Line upward each slice in the corners and then that there are no gaps betwixt the pieces of stripping.[10]

    • If you lot're weather stripping a window, make certain you lot apply a piece to the bottom edge, as well.

  10. ten

    Exam the door or window to brand certain it opens and closes properly. After yous've installed all of your stripping, endeavour opening and closing your door or window carefully. Check that information technology opens without sticking and that you can close it tightly.[eleven]

    • Be aware that you may need to push or pull the window or door more firmly at first because of the new stripping.
    • If you're having significant problem opening or endmost the window or door, adapt your weather stripping as necessary.

    Ad

  1. i

    Measure the bottom of the door frame. Identify ane cease of a tape measure on the inner border of i side of the door frame. Pull the measure taut along the ground to the inner border of the other side. Note what the measurement is. This is how long you lot'll demand to cutting the door sweep.[12]

    • Jot the measurement down on a piece of paper or type information technology in the notes app on your phone then y'all don't forget it.

  2. 2

    Cut the metal door sweep to the right length with a hacksaw. Mark the length yous measured on the door sweep with a pencil or marker. Clamp the sweep to a work table with the section you're going to cut hanging off the edge of the table. Apply pressure as yous push button the saw against the sweep and away from you. Repeat these pushing strokes until the saw cuts through the sweep.[13]

    • Always wear safety spectacles when cutting with a saw to protect your eyes from droppings.

    Tips for Cut with a Hacksaw

    Choose the right bract. Brand sure your hacksaw is fitted with a bract that works on metal, not 1 that's just for wood.

    Push, don't pull. Hacksaws only cut on the push stroke, and so you don't need to pull it dorsum through the sweep. Instead, you can lift it up and bring it back to the starting position.

  3. 3

    Place the sweep at the lesser of the inside of the door. Position information technology and so that the flexible bottom slice of the sweep just grazes the flooring. This will seal the gap underneath the door while also preventing the sweep from dragging against the floor when yous open and close the door.[fourteen]

    • You lot can check that your door sweep is aligned properly by looking underneath the door. If you lot tin can see light coming through, motion the sweep downwards a petty until all of the light is blocked.

  4. four

    Mark spots for the screws on the sweep and pre-drill pilot holes. Utilize a pencil to brand a marker where each of the provided screws volition go along the door sweep, spacing out the airplane pilot holes evenly in a straight line. For example, if you have 3 screws, make one hole on each side of the sweep so 1 in the center. Line up the drill bit with the marks and pull the trigger to drill through both the sweep and the door itself.[15]

    • Your door sweep should come with iii to 4 screws. If it doesn't, you can use whatever #6 screws.
    • For #half dozen screws, utilise a drill flake that's at least three⁄32 inch (0.24 cm) in diameter.

  5. v

    Use a screwdriver to insert the screws into the holes. Place i screw in each of the holes and tighten them with a screwdriver until they're completely secure. This volition secure the sweep to the door and then information technology won't hang off or come up loose.[16]

    • Test the door by opening and closing it a few times. If you lot observe the sweep is getting stuck, unscrew it from the door and arrange it as needed.

    Advertisement

  1. i

    Remove whatsoever old weather stripping that's already on the door. Use your hands to carefully peel off the piece that is currently on your car door. Make sure to pull up what you can of the adhesive layer underneath the stripping, also.[17]

    • In that location may exist screws in the stripping, which holds information technology in place. Unscrew them and fix them aside.
    • If you're having trouble peeling off the electric current slice, apply adhesive remover to it and let it soften for fifteen to 20 minutes before trying once more.

  2. two

    Use brake cleaner to articulate out the channel, then dry it with a towel. This volition get rid of any remaining adhesive residuum or dirt in the channel before you place the new stripping downwardly. Agree the can nearly 2 anxiety (0.61 m) from the door jamb and spray it along the channel. Wipe information technology off with a clean towel to remove any droppings.[18]

    • If y'all accept sensitive skin, wear rubber gloves when using brake cleaner.

  3. 3

    Apply a thin line of weather stripping agglutinative along the channel. Less is more than when it comes to the adhesive. Squeeze the tube to lay a bead of glue downwardly the groove where you'll identify the weather stripping.[19]

    • You lot tin buy weather stripping adhesive from an auto parts shop or an online retailer.

  4. iv

    Buy generic or custom weather stripping based on your preferences. While you tin purchase generic weather stripping at any auto parts store, you tin can also go a piece that'southward specifically designed to match your motorcar'due south brand and model from the service department at your dealership. Custom stripping is more guaranteed to seal tightly effectually your machine doors.

    • If you aren't sure what to use, phone call your dealership or an auto technician and ask their stance.
    • Custom weather condition stripping will be more expensive than generic stripping.

  5. 5

    Identify the new piece in the channel, pressing it firmly onto the adhesive. Line upwardly the new weather stripping in the groove around the door. Push down on the stripping in one case it's aligned so that the adhesive holds it in identify.[20]

    • If you notice whatsoever spots where the agglutinative oozed out and hardened, use the brake cleaner to wipe them away
    • If you had to remove any studs when you peeled off the one-time atmospheric condition stripping, spiral those back into their proper places in one case you lay down the new slice.

  6. 6

    Let the agglutinative dry out for 45 minutes before closing the door. Subsequently the gum is completely dry, you can close your car door. However, keep in mind it volition exist harder to close at first because of the new prophylactic.[21]

    • To make your new conditions stripping last longer, you can spray it with a prophylactic seal protectant subsequently the adhesive has dried.
    • You can as well spray silicone on the weather stripping to forbid ice and snow from sticking to it in the winter.

    Advertizement

Add New Question

  • Question

    How do you replace the atmospheric condition stripping on an exterior door?

    Jacob Pischer

    Jacob Pischer is a Home Improvement Specialist and the Owner of Helpful Annoy, a home repair service in Portland, OR. With over four years of experience, Jacob specializes in a variety of handyman services including pressure washing, cleaning gutters, repairing drywall, fixing leaky plumbing equipment, and repairing broken doors. Jacob studied at Madison Area Technical College and has a background in real estate investment.

    Jacob Pischer

    Home Improvement Specialist

    Expert Answer

    Support wikiHow by unlocking this adept respond.

    Commencement, employ a putty knife to have all of the old weather stripping off the door. You want to have a squeamish, make clean surface for the adhesive. Then, installing the new stuff is simple—information technology's usually but double-sided mucilaginous tape on one side, and yous put it on the door jams.

Ask a Question

200 characters left

Include your email address to get a message when this question is answered.

Submit

Advertizing

Things You'll Demand

  • Foam adhesive weather stripping
  • Cloth
  • Soap
  • Record mensurate
  • Pencil
  • Utility knife or scissors
  • Hammer and nails (optional)
  • Staple gun and staples (optional)
  • Adhesive remover (optional)
  • Door sweep with screws
  • Record measure
  • Hacksaw
  • Safety glasses
  • Pencil or marker
  • Work table
  • Clamp
  • Drill
  • Screwdriver
  • Brake cleaner
  • Cloths
  • Weather stripping adhesive
  • Weather stripping
  • Rubber seal protectant (optional)
  • Silicone spray (optional)
  • Adhesive remover (optional)

References

About This Article

Cheers to all authors for creating a page that has been read 36,080 times.

Did this article help y'all?